Alvin Indoor Furnishings X 3 XB User Manual

Professional Spacesaver  
For models X-3-XB, X-4-XB,  
X1-3-XB, X1-4-XB, XII-3-XB. XII-4-XB  
Assembly Instructions  
Tools Required: Phillips screwdriver, drill with 1/16" bit.  
B 1pc Tabletop  
C 2pcs Rear Extension Tubes  
Parts Included:  
(Shipped in  
A 1pc Leg Frame  
separarate box)  
D 2pcs Front Extension Tubes  
F 2pcs Height  
E 2pcs Floor Glides  
H 12pcs 1/2"  
Adjustment Knobs  
Wood Screws  
G 2pcs Leg Support Braces  
½" Screws  
To Assemble:  
1
Unpack all parts and inspect to confirm that all are present.  
( )  
Unfold base A .  
2
3
4
( )  
( )  
Insert rear extension tubes C completely into frame A and  
( )  
loosely hand-tighten knobs F .  
( )  
( )  
Insert front extension tubes D into frame A .  
( )  
Place table top B with preferred side facing down on carpeted or  
5
protected floor. Place supplied cardboard template on board surface  
with edge of template at front edge of board. Left and right edges of  
template should be an equal distance from each side of the table top.  
Using a 1/16" drill bit, gently drill ¼" deep holes where indicated on the  
template (red squares for 24" x 36" top or black holes for 31" x 42";  
template marked XB-II is for 36" x 48" top). Remove template.  
Figure 1  
Wrap masking tape ¼" from drill bit end to determine drilling depth.  
Take care to drill only ¼" deep to avoid drilling through and damaging  
table top surface.  
TIP  
( )  
onto the  
Using the Phillips screwdriver, screw the leg support braces  
G
6
7
( )  
tabletop B as shown in Figure 1.  
Carefully turn table frame upside down and place on top of  
( )  
tabletop. Align holes in front leg extensions D with holes in table  
( )  
top as shown in Figure 1. Fasten all ½" screws H and tighten  
securely. Use care not to overtighten and strip.  
Carefully return table assembly to the upright position. Adjust table  
8
( )  
top to desired height using height adjustment knobs F .  
You’re finished and your table is ready to use as shown in Figure 2.  
Figure 2  
Folding Table:  
Drop all extension tubes down to their lowest positions. Lift top up until  
( )  
( )  
the front extension tubes D disengage with the support braces G , then  
move the left leg assembly in until it is flush against the rear frame assembly.  
Next move the right leg assembly in flush against the left leg assembly.  
Gently lower the table top down flush against the right leg assembly.  
The table is now ready for storage.  
Professional Spacesaver Models  
X-3-XB  
X-4-XB  
XI-3-XB XII-3-XB  
XI-4-XB XII-4-XB  
©2008 ALVIN & COMPANY, INC. P.O. Box 188, Windsor, CT 06095-0722  
Phone: 860-243-8991 Toll-Free: 800-444-2584 • Fax: 860-242-8037 • Toll-Free Fax: 800-777-2896  
LIT-A8002 4/08  
 

Aarrow Fires Stove AFS1221 User Manual
Aastra Telecom Telephone 480i SIP User Manual
Acer Computer Monitor G195HQ User Manual
Acer Laptop MS2231 User Manual
Actiontec electronic Network Card 802UIG User Manual
Agri Fab Paint Sprayer 45 02934 User Manual
AMX Stereo Receiver NXC VOL4 User Manual
Atlona TV Cables ATP 14009 User Manual
Audiovox Remote Starter APS 687N User Manual
Axor Plumbing Product 4335XX0 User Manual